RF-Max Digimax 210 Manual de usuario descargar pdf (Pagina 3)

Keene Electronics Catalogue 2005Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

107

Remote controls Home automation Video tapes & accessories

Computer interface

Consists of the programmable X10

transmitter module and PC software. Use

your PC to program the module with timed

commands as required. The module then

works stand-alone even when the PC is

switched off. The module plugs into a 13

amp socket and will send and receive

commands across the house circuit. Signals

may be received from one or more

commanders (i.e. transceiver modules,

timers or any other combinations),and are

sent to be dealt with by receiver modules

(appliance or lamp switches, etc). The

computer interface module can send complex commands to any

module or switch. Unlike some of the other devices it can address

items across all house and unit codes and so can control up to 256

different addresses. In addition command groups can be set which

have sequences (i.e. A3 - turn on; B5 - go to half way; C6 - turn on and

then turn off after two minutes) and which can be triggered via

signals sent by a transceiver (actioned by a user pressing a remote

control button) or by a timer, or actioned via a programmed sequence.

Full functionality is programmed using the software supplied, allowing

any address to receive a command at intervals of not less than one

minute. The programme is downloaded to the computer interface

module via a serial cable (included). The computer interface module

has its own battery back-up power supply and will retain all of the

programming indefinitely as long as the power socket is switched on,

and for up to seven days in the event of a power failure or if the

socket is switched off. Thus the computer interface module can be

programmed and then taken to a different location for use (for

example by an elderly relative who has no PC, or perhaps at a second

home). The software is user friendly, operates under the Windows

environment and is continually updated. (A MAC version is available,

although not supplied). Note - the power socket into which it is

plugged must always be switched on.

[CM11U] £49.99

IR Command Centre

This unit lets you use an infra-red

remote to control X10 modules. It is

designed to be used with the

universal X10 remote although of

course you could also use this

remote to "teach" any compatible

learning remote such as the Pronto

or Marantz RC5000 etc. As well as IR

operation it also has its own keypad

for direct push button control of up

to eight devices.

[IR7243] £34.99

Mini timer

* As easy to program as an alarm clock

* 4 timers with two schedules each per day

* Manual 15 min delay feature

* 8 device keypad with "All On" & "All Off"

The mini timer resembles a conventional

alarm clock with an LED time display and

control buttons along the top, and enables

you to send manual commands to X10

addresses 1 to 8. It can send two 'on' and

two 'off' timed commands to each of unit addresses 1 to 4 or 5 to 8

which can either be set to precise times or to vary within 30 minutes

of a set time. There is an alarm function on either address 1 or 5

which activates a buzzer as well as sending a command. There is a

'sleep' function which can be used to send 'on' or 'off' commands at

any time from 15 minutes to over 8 hours ahead. An additional

feature is a button which will send an immediate 'on' command to all

lights set to the same house code (whether via a lamp module or a

wall dimmer switch). There is also an 'all units off' function allowing a

command to be sent instructing everything connected to the house

code to switch to the 'off' position. The mini timer sends its own

commands to modules and switches and there may also be other

signalling devices which you may wish to use. As with all of the X10

equipment, the mini timer works with a house code and a unit code

which can be easily changed at any time. More than one mini timer

can be used through the use of the house code system. For example,

there might be a circuit controlling, say, some lights and some

appliances which could be designated as circuit A and controlled by

remote controllers set to circuit A. Another completely separate circuit

could operate within the home, controlling another grouping of

devices. There will be no interference between those circuits and up to

16 circuits can exist at once. UK mains adaptor included.

[MT7222] £27.99

Wireless (RF) transmitters (things that send

RF commands to be translated into X10)

To be used in conjunction with the TM12U transceiver module,SC2800

Telephone Base Station etc which converts the RF into X10 commands

Telephone Base Station

An improved and updated

X10 telephone responder

TR7251, the SC2800 now adds

an excellent range of home

security options in addition to

telephone appliance control.

Once configured you can dial

into your house from

anywhere in the world and

switch on or off any X10

controlled appliance. Not

only that, the SC2800

provides some serious capability for home security. It's capable of

monitoring up to 16 wireless sensors, and, in the event of an alarm

condition (ie a trigger on one of these sensors) it can be set to

automatically dial out (on up to four different telephone numbers)

and playback any message you've pre-recorded. The SC2800 contains

a built in siren and can also trigger any other external X10 controlled

lights and sirens. Since all the alarm sensors are wireless it makes for

very easy installation yet provides a powerful and flexible alarm

system with full X10 integration and telephone control. It also acts an

X10 transceiver module (the base station on its own provides

telephone control and X10 push button control), and is compatible

with the DM210 thermostats. All in all a great X10 product.

Order code [SC2800] £89.99

Also available (with other components) as part of the MS9700 security

kit.

KR21E Key Fob remote (for easy arm/disarm)

[KR21E] £29.99

SM600 remote control (for full remote system control)

[SM600] £24.99

GB10E glass break sensor

[GB10E] £34.99

DS10E Door/window sensor

[DS10E] £29.99

MS10E PIR motion sensor

[MS10E] £49.99

RF transmitter modules for use with the SC2800 Telephone

Base Station

See SC2800 details above Also available (with other components) as

part of the MS9700 security kit.

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

RF-Max Digimax 210 Manual de usuario Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Termostatos RF-Max Digimax 210